ASPHALT, A REALY INERESTING LIQUID

Resisting Failure if Treated with Care

 

A pavement is about 93-96% rock, by weight, however it seems that there is a strong belief that by properly modifying the asphalt all problems can be solved. Asphalt or more properly, asphalts have served us well, even before modification. The properties of asphalts are primarily determined by their crude sources, however blending crudes or asphalts can at times produce an asphalt that performs better than either of the components. Modifying asphalts can also enhance their properties. However, it is important that we keep in mind that its performance depends to a great extent to its ability to flow, and its ability to suppress hardening as time goes.

Rutting is Not an Asphalt Failure. Asphalt is a liquid whose job is to flow in response to stress. If a pavement ruts, it is either ground by studded tires, or the aggregate size or the gradation is improper. If the stress is greater than the aggregate can handle, rutting occurs with the asphalt doing what it is designed to do, flow. Modifying the asphalt can affect how fast the flow occurs, however it is the aggregate properties that affect the rutting.

Many Aggregates Prefer Water to Asphalt. Asphalt doesn’t work well if it can’t stick to aggregate. Water can interfere with adhesion. One cause can be in the asphalt itself. If it is produced from crude oil that had been treated with caustic soda, it will contain soaps that will make the asphalt itself water sensitive. That has been solved by lime treating the crude. Antistrips are used to aid adhesion; however it has been shown that with some antistrips the effect wears off which allows water to lift the asphalt off of the rocks. There is one antistrip that combines chemically to aggregate and provides long term durability.

Non-load Associated Cracking Occurs when the Asphalt Cannot Relax Stresses. The fluidity of the asphalt is essential to prevent cracking. Trying to make the asphalt stronger only makes the matter worse as its maximum tensile strength is about 1000 psi. Portland cement cannot defeat thermal stress so don’t expect asphalt to do so. The solution is to have a binder that can relax stresses faster than they build up.

Pavement Slippage. Slippage occurs when of tack coats and primes are not used properly.

Fatigue Failure. There are suggestions that asphalt could be modified to increase its stiffness so that the pavement thickness could be reduced. Again it must be remembered that it is the aggregate that carries the load, in compression, not the asphalt. However fatigue failure occurs in tension, and again the tensile strength of asphalt is much less than that of aggregate. The pavement is stretched underneath the wheel path, and between the wheel paths. However, tensile failure is often really crack propagation, thus additives that stop crack propagation such as tire buffings may be of value.

chemistdunning@gmail.com, http://www.petroleumsciences.com

Advertisements

SOME BASIC CAUSES OF PAVEMENT FAILURE

Basics

INTRODUCTION

There are certain basics with respect to pavement failure that have existed since the first pavements were laid. Pavements crack, pavements slip, water damages them, and pavements rut. Irrespective of the tests used to evaluate pavements, failures have the same basic causes.

CRACKING

No matter where the cracking occurs, it is caused by the inability of the asphalt to relax the stresses, and must rupture.

Fatigue Cracking. Stress and strain are what are called tensors, which means that a pavement can be under compression and tension at the same time, but in different directions. While a tire compresses a pavement downward, it forms a deflection basin which causes the pavement to go into tension in both horizontal directions. Many years ago we used data from deflection testing and, assuming a parabola, did a line integral to calculate strain. If the pavement is not strong enough, the asphalt is stretched too far, separates and a crack forms in the wheel track. Also a crack may form between the wheel tracks.

Longitudinal Cracking on Joints. The joint between two passes are especially week. Inside any one pass of the paver, some aggregate willbe on both sides of any plane or slice inside of the pavement. In fact, when sample undergoes an indirect tensile test such as is done in stripping tests, rocks actually fracture. A joint, however, is held together only by the asphalt layer, which has a tensile strength of about 200-1000 psi, depending on the temperature and shear rate. If the asphalt in the mix can flow vertically in response to thermal stresses, the crack won’t form. However, if the stresses exceed that at the joint, a crack forms. As a result the pavement on either side of the crack can shrink or expand independently. Often what happens then is that the pavement sections shrink away from each other in the cold, but do not expand completely back together in the heat. For that reason it is crucial to follow proper technology of forming a joint.

Thermal Cracking.  The mechanism of formation of thermal or non-load associated cracks is again the lack of the asphalt to be able to relieve thermal stresses by flowing vertically up when the pavement is hot and vertically down when the pavement is cold.

PAVEMENT SLIPPAGE

From time to time the pavement will shift. In one project I has on at the LAX airport, a 2” lift was slipping on a 4” lift from landing of air traffic. A core was made of the section so it waw possible to observe a daily slippage. Two sources of the problem. First, it was supposed to be 4” over 2”. Secondly, if there was a tack coat, it had been ruined as a result of a dust storm. To prevent slippage a prime needs to be used between the base and pavement, and a tack coat between two lifts.

RUTTING

There are two causes of rutting, improper aggregate gradation and studded tires.

Gradation.  Asphalt itself is too weak to stopthe flow of the mix by itself. If the coarse aggregate in the mix cannot interlock themix has to rely on a mastic composed of the fines and asphalt, which cannot carry the load. The solution is a coarse gradation with no humps in the fine mastic area.

Studded Tires. Research is under way on how to solve this problem. Harder aggregate has helped, but no solution is available now.

WATER DAMAGE

If the pavement is not protected from water damage, all of the above is blowing in the wind. There are data that suggest that even pavement protected by amine or lime antistrips will lose much of its strength thus cannot complete its design life. Many aggregates are wetted by water better than asphalt so that if the surface cannot be permanently altered to prefer wetting by asphalt, eventually water will replace the asphalt.

Robert L. Dunning. www.petroleumsciences.com, blog asphaltwaterproofing.wordpress.com